3-1 kind of a weekend

October 4, 2011

I’m going to make this a short one and not a 1000 word blog. 3-1 kind of weekend? It’s a play on words title I chose. It’s referencing my beloved San Francisco 49ers record into a young season. Niner fans have been suffering for about 10 years and milking it ‘while it lasts’ is one thing that I will be doing. I’m also going to share with my readers 3 various jobs that I’ve done. Hell, I’ll just include a YouTube video showing you a process of this coral job I did.

So I get this order for this red coral job that I needed to supply into a tear drop shape with grooves cut into them. You may remember a blog I wrote on this Turquoise job I did called ‘Turquoise Grooves‘ which explained the whole process.

I mapped out how and where I’d like my grooves to be cut on this calcium induced piece of red coral using a small disk drill bit.

As you can see, this is the process of mapping out lines into the tear drop coral.

Here’s that video I promised showing you the process.

You may notice that I cut the lines deep so I have room to make the grooves.

Here’s the finished product. I filed the grooves in and used various custom made drill bits to give it that rounded look between each groove.

I finished it off with a 1mm hole so that some sort of post would sit into the drilled area.

So I get this David Yurman two toned ring in that needed a new Moonstone cut into it.

I supplied a nice cushion cut cabochon Moonstone to sit into the bezel.

The stone should sit perfectly inside and I recommended to my customer to glue it in and to do a light hammer on the walls of the bezel to give it that extra secure fit into the mounting.

And finally, I machine cut, to the millimeter, diamond shape cut blue sapphires that I supplied into this white gold ring.

As you can see, they go from large, medium, to small.

The blue sapphires sit perfectly into the desired area and some how, I kept this blog from reaching 400 words which is a new record for me. Hopefully, I’ll have another blog out and running by the end of this Friday. Till next time…

Advertisements

Turquoise Grooves

July 29, 2011

I’ve been slacking once again with my blog entries. I do apologize, but I have a good one in store for you today – Turquoise. If you come to my office, you’re bound to find turquoise rough just hanging around somewhere. I actually just stopped typing to take a peek into my workshop to catch a glimpse of a turquoise rough just hanging next to the window. So, before I describe my most recent endeavor, let me share some information about turquoise.

Turquoise is an opaque stone, which means it is not see-through. It has a hardness of just under 6 on the Mohs scale. Turquoise is found in or near copper deposits/mines as it depends on the presence of copper ions for it to form. It is composed of a hydrous hydrate of copper, aluminum and phosphorus elements. Turquoise was one of the first gem stones to be mined. It comes from all over the world (Afghanistan, Africa, Australia, Brazil, Chile, China, Egypt, Iran, Israel, Mexico, Siberia, Tibetan, Turkey and the US of A). The particular turquoise I am working on comes from a unique mine located in Arizona. The western state is home to some of the largest mines in the world including the ‘Sleeping Beauty’ mine where my stone originates. Sleeping Beauty turquoise is a solid stone with no matrix that ranges in color from Royal Blue to a very light Sky Blue. Generally speaking, turquoise color ranges from green to greenish-blue to blue.

And what better way to finish off this little digression on turquoise with these interesting facts! Did you know that no English gentleman of the 17th century was not regarded as well dressed or well adorned unless he wore jewelry of turquoise? This stone was so highly valued that all 79 of the emeralds in the crown that Napoleon gave his consort Marie Louise were replaced with Persian turquoise cabochons. In my opinion, I prefer sleeping beauty turquoise for its color, quality, and the nice value it carries. I personally think it’s better than the Persian stuff. Again, that is my opinion.

I made a special order ring about a year ago with diamonds around the mounting and I supplied it with a high cab sleeping beauty turquoise with grooves that I carved into it. I would of blogged about it but I didn’t have a blog at the time. But now I do!

My customer has asked me to cut 2 matching oval shaped sleeping beauty turquoise with the same carved grooves for some earrings that she wants to make.

Here’s the top view of the Carved Sleeping Beauty Turquoise I supplied and cut.

Here’s a side view. Notice the classy look on the ring, yet the Turquoise is still the center of attention.

So I go pull out some Sleeping Beauty Turquoise rough.

Here’s another angle. I’ll be slicing through this to get the deserved size I want before I preform the turquoise.

I quickly preformed the 2 pieces of turquoise I need with a flat bottom by hand after I sliced it from its rough form.

Here’s another angle. Notice how high the dome is. It gives me room to carve into the turquoise and give it its groove without sacrificing too much of the height of the stone.

I glued the turquoise onto the dopping stick as a guide so I can start going into detail with the desired size. I’m using a millimeter gauge to measure the 16x12mm size I need. If you don’t know what a dopping stick is, click this link ‘here‘, which should take you to one of my first blogs explaining the steps into the gem cutting world.

you have to apply the softest touches to the disk or it’ll eat away at your turquoise.

I ended up with 2 matching color, cut, and shaped beauties (no pun intended) after I used the preforming machine.

Here’s a side view of the matching turquoise cabochons on the dopping sticks.

I removed it off the wax/glue and I started to pencil in the areas where I’d be carving in the grooves.

Here’s a better look. What’d did you expect? A pencil is an awesome tool sometimes.

I just started filing in the grooves. Sorry, my bench light is ruining the picture but you get the idea.

I’m using my filer to cut into the turquoise. By doing it by hand, you have more freedom in your movement.

I’m working the edges on the turquoise here.

I finished using the hand file. It sort of looks like a preformed state after I filed it.

I started using a specially designed drill bit with a round disk with an inward curvature to round out the grooves.

I took it to my lapidary machine and gave it a little nice polish on top to get these 2 beauties.

Matching cut pairs.

That was a fun and challenging project. Next week I’ll start putting some of my special orders I get that  involve some sort of gem cutting + whatever I make for the gemstone. Till next time…